Looking for Burbank Driveway Gate Contractor? We survey the entrance before quoting: the fall across the opening, the run-back room, and where power can reach. We serve Burbank and the surrounding neighborhoods.
A driveway gate is the largest moving thing on most properties, and the posts carrying it decide everything about how it behaves.
We survey the entrance before quoting: the fall across the opening, the run-back room, and where power can reach.
Swing, slide or cantilever is a decision the ground makes rather than a matter of taste. We tell you which the site allows.
Cheaper to build and right on most flat or falling drives, with nothing on the ground to fill with grit.
They need room behind the opening. Up a rising drive an inward swing catches before it is fully open, which is the mistake we are called out to fix.
The answer on rising drives and tight properties, and the only option once an opening is too wide for swing leaves.
A slider needs somewhere to go, roughly the width of the opening again along the fence line.
Carried on rollers set back along the fence with no ground track at all, so there is nothing to clog or break out of the driveway.
More run-back room and more structure, which is why it costs more. On a debris-prone entrance it is often the only sensible choice.
Automatic gates around Burbank combine a physical gate with mechanical and electrical equipment. When one stops working the problem is not necessarily the gate itself — it may be the operator, motor, controls, sensors, remotes, safety equipment or wiring.
We service gates for apartment buildings, businesses and parking areas across Burbank, where a gate that fails is a problem the same morning.
Safety sensors, keypads, remotes, receivers and intercoms all have to agree with each other. We troubleshoot the complete system rather than swapping parts.
From a walk gate that no longer latches to a large automatic entrance, we repair gates on Burbank homes and multifamily property alike.
Wood gates split, warp and loosen in the Los Angeles County sun. Metal gates develop alignment problems, damaged hardware or failures at welded joints.
The operator opens and closes an automated gate. On a busy Burbank driveway that is hundreds of cycles a month, and they eventually develop mechanical or electrical problems.
Driveways around Burbank are rarely flat, and a swing gate opening up a rising drive will catch the ground before it is fully open.
We measure the fall across the opening on site, which is the five minutes that stops an expensive mistake.
We explain what we found, what it will cost, and what we would do if it were our own property.
We measure the fall and the run-back before anything is fabricated.
Fabricated for your entrance rather than trimmed from a stock size.
Built to take an operator later even if you are not fitting one now.
We quote after seeing the property, always. Anyone giving you a firm figure without knowing your ground is guessing, and that guess is rarely in your favour once they arrive.
Two things surprise people on cost: removal and disposal of what is already there, and ground that turns out to be rock or roots. Both are real labour and both get priced honestly up front.
Ask what the hinges are rated for against the actual weight of the leaf, and how deep the gate post is going. Undersized on either is why gates start dragging.
Ask who services it afterwards and whether they carry parts. Plenty of gates get installed by someone who never comes back.
Yes, if the gate moves freely and the posts are up to it. Tell us at the design stage and we will build it automation-ready, which costs very little now and saves a rebuild later.
If the frame is square and the posts are sound, it is a repair. We tell you honestly which side of that line your gate sits on before quoting anything.
Most of what we repair was put in by somebody else. We are not precious about it — we just fix what is wrong.
The first thing we check on a Burbank callout is whether the leaf is still square and whether the post has moved. Almost everything else follows from those two answers.
We start by moving the gate by hand. How it feels tells us more than any description over the phone: where it binds, where it drops, and whether the problem is the gate or the post holding it.
If the structure is sound we repair it. Posts that are still solid, a frame that is still square and hardware that can be replaced usually add up to a repair rather than a rebuild.
We would rather fix what you have than sell you something new. Telling a Burbank customer their fence has years left in it is a shorter conversation, but it is the one that gets us called back.
Burbank sits within our regular working area alongside Toluca Lake, Universal City and Cahuenga Pass. Being local matters more than it sounds: it is the difference between coming out this week and coming out next month.
Most of our work is within a short drive of Burbank — Toluca Lake, Universal City, Cahuenga Pass and the rest of Los Angeles County. We are not sending someone across the county to look at your fence.
Coastal air reaches further inland than people expect and finds any gap in a coating. On steel that means rust starting at the welds and the cut ends first.
Heat, damp and grit are what wear a gate out. Tracks fill with debris, hinges dry out, and the ground under the posts moves enough through the year to change how the gate sits.
A repair is often the same visit. A new gate takes longer because it is built to your opening, and the posts need to be set and cured before it hangs.
Repairs are usually one visit. Fabrication work depends on the gate, and we will give you a realistic date rather than an optimistic one.
Every pin is a city we cover. Tap one to open our driveway gate contractor page for that city, or see the full list of service areas.
The 20 communities closest to Burbank that we cover. Same crew, same pricing.
(213) 282-7990
Text Us