Looking for Malibu Electric Gate Contractor? An automated gate is a gate plus equipment, and the equipment only works as well as the gate underneath it. We serve Malibu and the surrounding neighborhoods.
An automated gate is a gate plus equipment, and the equipment only works as well as the gate underneath it.
We size the operator to the actual leaf weight and duty cycle rather than fitting whatever is on the shelf.
Safety equipment, force settings and a manual release you know how to use are part of the job, not extras.
Sized to the actual leaf weight and how often the gate will cycle, not to whatever is in the van.
A residential unit on a commercial entrance does a year of domestic work every month, and it fails accordingly.
Keypads, intercoms, remotes and app control each solve a different problem. Most households need more than remotes.
An exit loop cut into the driveway is the upgrade people add later and wish they had first.
Photo eyes cover the opening, edge sensors cover the gate itself, and force settings stop it pushing through resistance.
We fit them, demonstrate them working, and show you where the manual release is.
Automatic gates around Malibu combine a physical gate with mechanical and electrical equipment. When one stops working the problem is not necessarily the gate itself — it may be the operator, motor, controls, sensors, remotes, safety equipment or wiring.
From a walk gate that no longer latches to a large automatic entrance, we repair gates on Malibu homes and multifamily property alike.
Safety sensors, keypads, remotes, receivers and intercoms all have to agree with each other. We troubleshoot the complete system rather than swapping parts.
Wood gates split, warp and loosen in the Los Angeles County sun. Metal gates develop alignment problems, damaged hardware or failures at welded joints.
We service gates for apartment buildings, businesses and parking areas across Malibu, where a gate that fails is a problem the same morning.
The operator opens and closes an automated gate. On a busy Malibu driveway that is hundreds of cycles a month, and they eventually develop mechanical or electrical problems.
Power at the gate is the question that decides most automation projects in Malibu: trenching a long drive is often the largest single cost.
Solar is genuinely viable here for gates with modest daily cycles, and it removes that question entirely.
You get a written price before any work begins, and we tell you plainly if replacement is the better value.
Operator matched to leaf weight and duty cycle.
Sensors fitted, forces set, and both demonstrated to you.
Established equipment we can still get parts for in ten years.
A service call is usually resolved the same visit. A full install depends on the gate and the power route, and we tell you which before we start.
Most automation installs are a day on site, assuming power is already at the gate. Running a new supply or cutting loops into the driveway adds to that.
You get a straight answer on the day. If the job needs something we cannot do well, we will tell you that too rather than take it on and hope.
We come out and look, we tell you what we found, and you get the price in writing before anything starts. If we think replacement is better value than repair, we say so.
Nine times out of ten it is a safety sensor — misaligned, dirty or failed. The system is doing exactly what it is designed to do with the information it has.
Yes. Most of the automation we work on was installed by someone who never came back.
Every automated gate has a manual release. We show you where yours is and how to use it, and battery backup will usually cycle the gate a number of times on its own.
Ask what safety equipment is included and whether they will demonstrate it working. Photo eyes and correct force settings are not extras.
Ask whether they moved the gate by hand before quoting. If they did not, they are quoting an operator for a gate nobody has assessed.
Power, sensors, controls and the gate itself all get tested. Guessing at an operator is how people end up paying for a control board they never needed.
We release the operator and move the gate by hand first. If it is heavy or binding, the fault is mechanical and no amount of work on the motor will fix it.
We quote after seeing the property, always. Anyone giving you a firm figure without knowing your ground is guessing, and that guess is rarely in your favour once they arrive.
There is no useful phone price for this. What moves the number is the length, the height, the ground conditions and whether there is an old fence or gate to remove. We look, then we put it in writing.
We would rather fix what you have than sell you something new. Telling a Malibu customer their fence has years left in it is a shorter conversation, but it is the one that gets us called back.
Replacement makes sense when several posts have gone along the same run, when the frame has racked out of square, or when repeated repairs have already cost more than half the price of new. Short of that, repair almost always wins.
Most of our work is within a short drive of Malibu — Westlake Village, Agoura Hills, Calabasas and the rest of Los Angeles County. We are not sending someone across the county to look at your fence.
We cover Malibu and the surrounding communities including Westlake Village, Agoura Hills and Calabasas, so we are rarely far away when something needs looking at quickly.
Every pin is a city we cover. Tap one to open our electric gate contractor page for that city, or see the full list of service areas.
The 20 communities closest to Malibu that we cover. Same crew, same pricing.
(213) 282-7990
Text Us