Looking for Malibu Electric Gate Repair? A gate that opens but will not close is almost always a safety sensor doing exactly what it was designed to do. We serve Malibu and the surrounding neighborhoods.
A gate that opens but will not close is almost always a safety sensor doing exactly what it was designed to do.
We test power, sensors, controls and the gate itself before quoting a part, because guessing at an operator is expensive.
If the gate binds by hand, no work on the motor will fix it. That check comes first on every callout.
A gate that opens but will not close is the classic photo eye fault: a dirty lens or a knocked bracket.
The system is behaving exactly as designed with the information it has. Cleaning and realigning fixes most of them.
Boards, transformers, receivers and batteries all fail, and battery backup can mask a mains fault for days.
That delay is why the cause so often looks unrelated to anything that actually happened.
If the gate is heavy or binding by hand, the fault is mechanical and no work on the motor will fix it.
An operator fighting a binding gate runs hot and usually takes its board with it.
Automatic gates around Malibu combine a physical gate with mechanical and electrical equipment. When one stops working the problem is not necessarily the gate itself — it may be the operator, motor, controls, sensors, remotes, safety equipment or wiring.
Safety sensors, keypads, remotes, receivers and intercoms all have to agree with each other. We troubleshoot the complete system rather than swapping parts.
Wood gates split, warp and loosen in the Los Angeles County sun. Metal gates develop alignment problems, damaged hardware or failures at welded joints.
The operator opens and closes an automated gate. On a busy Malibu driveway that is hundreds of cycles a month, and they eventually develop mechanical or electrical problems.
We service gates for apartment buildings, businesses and parking areas across Malibu, where a gate that fails is a problem the same morning.
From a walk gate that no longer latches to a large automatic entrance, we repair gates on Malibu homes and multifamily property alike.
Photo eyes in Malibu collect dust, cobwebs and sprinkler spray, and a dirty lens stops a gate as effectively as a failed board.
Battery backup also masks a power fault for days, which is why the cause often looks unrelated to anything that happened.
Estimates are free and there is no obligation. If the honest answer is that repair will not last, we will say so.
Power, sensors, controls, then the gate itself.
We tell you honestly when a system has been orphaned by its installer.
Checked and explained on every visit, because power cuts happen.
Most automation installs are a day on site, assuming power is already at the gate. Running a new supply or cutting loops into the driveway adds to that.
A service call is usually resolved the same visit. A full install depends on the gate and the power route, and we tell you which before we start.
One crew, one point of contact, and a written price with nothing hidden in it. We clear up properly at the end, which sounds like a small thing until someone does not.
We come out and look, we tell you what we found, and you get the price in writing before anything starts. If we think replacement is better value than repair, we say so.
It has to move freely by hand and the posts have to take the load. We check both before quoting rather than bolting a motor onto a problem.
Once a year is plenty for most residential gates. Cleaning the photo eyes and checking the hardware prevents most of the callouts we attend.
Every automated gate has a manual release. We show you where yours is and how to use it, and battery backup will usually cycle the gate a number of times on its own.
Power cuts catch people out. Battery backup keeps a gate running for days after the mains fault, so when it finally stops the cause looks unrelated.
Most automation faults we attend in Los Angeles County trace back to something simple: a dirty sensor, a flat remote battery, or a gate that has started to bind and is making the operator work harder than it should.
We would rather fix what you have than sell you something new. Telling a Malibu customer their fence has years left in it is a shorter conversation, but it is the one that gets us called back.
If the structure is sound we repair it. Posts that are still solid, a frame that is still square and hardware that can be replaced usually add up to a repair rather than a rebuild.
Price comes down to size, material, access and what has to come out first. A straight run on flat ground with a driveway beside it is quick. The same job down a narrow side return with a hedge in the way is not.
There is no useful phone price for this. What moves the number is the length, the height, the ground conditions and whether there is an old fence or gate to remove. We look, then we put it in writing.
Automation callouts in Malibu split roughly into three: something mechanical, something electrical, or a safety sensor doing exactly what it should. We work out which before touching anything.
We release the operator and move the gate by hand first. If it is heavy or binding, the fault is mechanical and no amount of work on the motor will fix it.
Ask whether they moved the gate by hand before quoting. If they did not, they are quoting an operator for a gate nobody has assessed.
Ask what safety equipment is included and whether they will demonstrate it working. Photo eyes and correct force settings are not extras.
Every pin is a city we cover. Tap one to open our electric gate repair page for that city, or see the full list of service areas.
The 20 communities closest to Malibu that we cover. Same crew, same pricing.
(213) 282-7990
Text Us