Looking for Burbank Driveway Gate Repair? A driveway gate that has started catching or dragging has usually been moving for months before anyone noticed. We serve Burbank and the surrounding neighborhoods.
A driveway gate that has started catching or dragging has usually been moving for months before anyone noticed.
We release the operator and move the gate by hand first, because that tells us whether the fault is mechanical or electrical.
Track, rollers, hinges, posts and footings all get checked together. A gate this size will not stay fixed if only one of them is right.
A slider does not jump its track without a reason: debris, a worn roller or a footing that has settled.
Lifting it back on takes ten minutes. Finding why it came off is what stops it happening again next month.
Rollers are consumable. They flatten, seize and break up, and a gate on failing rollers runs noisy and slow before it runs off.
If your gate has been getting louder over the last few months, it was telling you this was coming.
Reversing into a gate is more common than people admit, and the damage travels past where the car touched.
We check the frame for square, then the hinges, the post and the operator mounting before quoting anything.
Automatic gates around Burbank combine a physical gate with mechanical and electrical equipment. When one stops working the problem is not necessarily the gate itself — it may be the operator, motor, controls, sensors, remotes, safety equipment or wiring.
The operator opens and closes an automated gate. On a busy Burbank driveway that is hundreds of cycles a month, and they eventually develop mechanical or electrical problems.
Wood gates split, warp and loosen in the Los Angeles County sun. Metal gates develop alignment problems, damaged hardware or failures at welded joints.
Safety sensors, keypads, remotes, receivers and intercoms all have to agree with each other. We troubleshoot the complete system rather than swapping parts.
We service gates for apartment buildings, businesses and parking areas across Burbank, where a gate that fails is a problem the same morning.
From a walk gate that no longer latches to a large automatic entrance, we repair gates on Burbank homes and multifamily property alike.
Grit, leaves and the mulch that washes out of a bed after rain all end up in a Burbank gate track.
Most of the slider callouts we attend start there, and a brush along the track once a month prevents them.
You get a written price before any work begins, and we tell you plainly if replacement is the better value.
We find why it failed so the same repair is not needed twice.
Most track, roller and hardware work is done on the day.
If the gate has reached the end we say so rather than selling a fourth repair.
We come out and look, we tell you what we found, and you get the price in writing before anything starts. If we think replacement is better value than repair, we say so.
One crew, one point of contact, and a written price with nothing hidden in it. We clear up properly at the end, which sounds like a small thing until someone does not.
Wind is the one that breaks things. A closed gate takes the full force of it, and that load ends up in two hinges and one post.
Coastal air reaches further inland than people expect and finds any gap in a coating. On steel that means rust starting at the welds and the cut ends first.
Almost always the post has moved, dropping the far edge of the leaf so the latch and keeper no longer line up. Replacing hardware on a post that has tilted buys you about a month.
Most of what we repair was put in by somebody else. We are not precious about it — we just fix what is wrong.
For a gate that will not close or lock we try to get there the same or next day. It is a security problem, not just an inconvenience.
Replacement makes sense when several posts have gone along the same run, when the frame has racked out of square, or when repeated repairs have already cost more than half the price of new. Short of that, repair almost always wins.
We would rather fix what you have than sell you something new. Telling a Burbank customer their fence has years left in it is a shorter conversation, but it is the one that gets us called back.
A repair is often the same visit. A new gate takes longer because it is built to your opening, and the posts need to be set and cured before it hangs.
Repairs are usually one visit. Fabrication work depends on the gate, and we will give you a realistic date rather than an optimistic one.
Two things surprise people on cost: removal and disposal of what is already there, and ground that turns out to be rock or roots. Both are real labour and both get priced honestly up front.
There is no useful phone price for this. What moves the number is the length, the height, the ground conditions and whether there is an old fence or gate to remove. We look, then we put it in writing.
We cover Burbank and the surrounding communities including Toluca Lake, Universal City and Cahuenga Pass, so we are rarely far away when something needs looking at quickly.
Most of our work is within a short drive of Burbank — Toluca Lake, Universal City, Cahuenga Pass and the rest of Los Angeles County. We are not sending someone across the county to look at your fence.
Find out whether the gate is being built to match what is already there, and how close it will actually get. Honest answers about that are a good sign.
Ask who services it afterwards and whether they carry parts. Plenty of gates get installed by someone who never comes back.
Every pin is a city we cover. Tap one to open our driveway gate repair page for that city, or see the full list of service areas.
The 20 communities closest to Burbank that we cover. Same crew, same pricing.
(213) 282-7990
Text Us