Looking for Burbank Electric Gate Contractor? Safety equipment, force settings and a manual release you know how to use are part of the job, not extras. We serve Burbank and the surrounding neighborhoods.
An automated gate is a gate plus equipment, and the equipment only works as well as the gate underneath it.
We size the operator to the actual leaf weight and duty cycle rather than fitting whatever is on the shelf.
Safety equipment, force settings and a manual release you know how to use are part of the job, not extras.
Sized to the actual leaf weight and how often the gate will cycle, not to whatever is in the van.
A residential unit on a commercial entrance does a year of domestic work every month, and it fails accordingly.
Keypads, intercoms, remotes and app control each solve a different problem. Most households need more than remotes.
An exit loop cut into the driveway is the upgrade people add later and wish they had first.
Photo eyes cover the opening, edge sensors cover the gate itself, and force settings stop it pushing through resistance.
We fit them, demonstrate them working, and show you where the manual release is.
Automatic gates around Burbank combine a physical gate with mechanical and electrical equipment. When one stops working the problem is not necessarily the gate itself — it may be the operator, motor, controls, sensors, remotes, safety equipment or wiring.
From a walk gate that no longer latches to a large automatic entrance, we repair gates on Burbank homes and multifamily property alike.
Safety sensors, keypads, remotes, receivers and intercoms all have to agree with each other. We troubleshoot the complete system rather than swapping parts.
The operator opens and closes an automated gate. On a busy Burbank driveway that is hundreds of cycles a month, and they eventually develop mechanical or electrical problems.
We service gates for apartment buildings, businesses and parking areas across Burbank, where a gate that fails is a problem the same morning.
Wood gates split, warp and loosen in the Los Angeles County sun. Metal gates develop alignment problems, damaged hardware or failures at welded joints.
Power at the gate is the question that decides most automation projects in Burbank: trenching a long drive is often the largest single cost.
Solar is genuinely viable here for gates with modest daily cycles, and it removes that question entirely.
We give you the price in writing up front, and we do not start work until you are happy with it.
Operator matched to leaf weight and duty cycle.
Sensors fitted, forces set, and both demonstrated to you.
Established equipment we can still get parts for in ten years.
Ask whether they moved the gate by hand before quoting. If they did not, they are quoting an operator for a gate nobody has assessed.
Ask what safety equipment is included and whether they will demonstrate it working. Photo eyes and correct force settings are not extras.
We come out and look, we tell you what we found, and you get the price in writing before anything starts. If we think replacement is better value than repair, we say so.
One crew, one point of contact, and a written price with nothing hidden in it. We clear up properly at the end, which sounds like a small thing until someone does not.
It has to move freely by hand and the posts have to take the load. We check both before quoting rather than bolting a motor onto a problem.
Every automated gate has a manual release. We show you where yours is and how to use it, and battery backup will usually cycle the gate a number of times on its own.
Yes. Most of the automation we work on was installed by someone who never came back.
Power cuts catch people out. Battery backup keeps a gate running for days after the mains fault, so when it finally stops the cause looks unrelated.
Sun, damp and dust are hard on the equipment. Photo eyes collect cobwebs and grime, enclosures cook in the afternoon heat, and control boards do not enjoy either.
Most automation installs are a day on site, assuming power is already at the gate. Running a new supply or cutting loops into the driveway adds to that.
A service call is usually resolved the same visit. A full install depends on the gate and the power route, and we tell you which before we start.
Burbank sits within our regular working area alongside Toluca Lake, Universal City and Cahuenga Pass. Being local matters more than it sounds: it is the difference between coming out this week and coming out next month.
We cover Burbank and the surrounding communities including Toluca Lake, Universal City and Cahuenga Pass, so we are rarely far away when something needs looking at quickly.
Replacement makes sense when several posts have gone along the same run, when the frame has racked out of square, or when repeated repairs have already cost more than half the price of new. Short of that, repair almost always wins.
If the structure is sound we repair it. Posts that are still solid, a frame that is still square and hardware that can be replaced usually add up to a repair rather than a rebuild.
Power, sensors, controls and the gate itself all get tested. Guessing at an operator is how people end up paying for a control board they never needed.
Automation callouts in Burbank split roughly into three: something mechanical, something electrical, or a safety sensor doing exactly what it should. We work out which before touching anything.
Every pin is a city we cover. Tap one to open our electric gate contractor page for that city, or see the full list of service areas.
The 20 communities closest to Burbank that we cover. Same crew, same pricing.
(213) 282-7990
Text Us